Online repair manual

At Cadillac craftsmanship of our only standard – and experts take notice. Take our Escalade, Escalade ESV, Escalade EXT, for example. Edmunds.com praises Escalade family for such virtues as "endless V8 power, plush ride quality, more flexible than you might think, comfortable seats, plenty of lifting capacity of all the latest technological gadgets, best-in-class towing capacity". * Automotive experts on familycar.com call Escalade "large, distinctive and

WIRING information: 2004 Cadillac SRX WIRE WIRE color wires location 12V CONTINUOUS WIRE 12V wires in the harness, low current 12V ignition sources that should not be used to drive any of the high current positive circuits. Must go to battery 12V. LEJTENANTZelenyj ignition harness power door lock red/black (-) at the door lock switch inside driver's door power door unlock orange/black (-) at

CTS OC-2 is a plug and play interface that allow you to install an aftermarket radio Cadillac SRX and CTS vehicles. It will support operation Staro and factory amplified audio system. At Staro will play audio through front speakers when active. It also saves all the warning chimes and vehicle rear parking assist chime.
• Class II chain does not disable data bus vehicles, even if the interface fails.

Information on upgrading some OnStar ® 5 analog/digital-Ready OnStar ® systems for generation 6 dual-mode (analog/digital), this newsletter is produced with the information and procedures for dealer personnel should the owner wish to update their OnStar ® generation 5 analog/digital-ready OnStar ® system to a system of generation 6 dual-mode (analog/digital).

Disassembly
1. thoroughly clean and dry air valve bodies. Clear the balls. Remove each valve train.
2. put the valves, springs and sleeves to clean surface as deleted. Remove the solenoids, sensor, screens, servos and battery assemblies.

Our all new, all-steel, retro air cleaner is based on the style and size of 1951-56 Oldsmobile and Cadillac air purifiers. This exciting new product would look at home in any street rod, hot rod or traditionally styled "perfect" car.

All-new 2010 Cadillac SRX midsize crossover represents a significant departure from its predecessor by rear drive as a record of more comprehensive and very style. It is based on General Motors all new global midsize front drive crossover architecture (also known as Theta-Epsilon). The new SRX has dramatic presence, from his great shield grille and large, the Centre is located a wreath and Crest for vertical taillamps, modern "tail", which include more than 40 LEDs on a lamp.

Global a serial data transmission electric

1995 the engine PERFORMANCE of General Motors Corp. delete overhaul & Cadillac installation; Contest, Deville, Seville
* Please read this first * caveat: when you disconnect the battery in your computer and the memory system of vehicles might lose data memory.

This Motor blower has undergone some changes in the design so changed as installation procedures. The original engine was a two piece Motor and wheel provided with screw. GM changed the design in one piece unit with heat shield, and fiberglass wheel is pressed.

Remove factory radio
Step 1: Locate and delete the two (2) screws Phillips plastic top panel, which covers the radio controls and air conditioning. They should be located next to leverage air conditioner ventilation directly above (2) air conditioning vents. Pull out the Plastic Panel gently from top to remove it from the dash.
Step 2: radio will be undertaken in two (2) 7 mm bolt screws; one on each side of the radio. Delete both.
Step 3: to remove the radio, pull firmly. Unplug all connectors (1 blue, 1 white and 1 black) from the back of the radio. Disconnect the antenna cable from the back of the radio. Radio can now be removed from the dash.
Step 4: since the opening is so big, in Tyre, a doctor recommends that you use plastic mounting bracket, attached to the bottom of the radio is simply deleted.
This bracket can be attached to the bottom of the mounting plastic radio and assure you that this set of properly aligned and fixed on the dash.

Radio installation kit
STEP 1:
Connect all the necessary cables and harness connectors. Connect the antenna cable in the new radio.
Insert the radio and set to open in tyre. Secure mounting kit screws, two (2) 7 mm bolt, initially in auto workers factory radio.
STEP 2:
Attach the plastic dash, which covers the radio controls and air conditioning.
Now the installation is complete

Wiring instructions:
Power and dynamics of the wires needed to connect new radio are attached to the wire connector located inside the vehicles tyre. Install the doctor strongly recommends that you use additional MMC snap-in on the wire that is specifically designed for the snap-in connectors Automotive wire tyre. This will keep you from cutting wires vehicles. This optional snap-on wire will have wire on the other connector that will allow you to splice the wires to the new station. Your only option is to cut car connectors wire dash and splicing of new radio stations directly on these wires wires. Optional snap-ins on the wire takes all the guess work, trying to figure out what each wire is wire tyre vehicles. Optional snap-ins on the wire to tell you what each wire.

Source

Enhance and support the vehicle, allowing the pendants hang free.
Remove the wheel.
Disconnect the plug electric shock-absorber.
Supports arm control with Jack stand or screw Jack to release the spring load.

Step 1-vehicle preparation
Remove the negative battery cable. With the vehicle standing on a smooth solid surface chock the front wheels. With the help of Jack, the nominal weight of your car, to raise the wheels from the ground. Less weight on Jack stands with the nominal weight of the vehicle, upon being satisfied that the suspension is fully extended. (Do not use wood or concrete blocks to support the vehicle.)
Step 2-remove the coil spring
Put a Jack axis on the left side of the vehicle. Remove the lower bolt with a shock absorber. Lower axis until the coil spring may be removed. Warning: do not put tension or stress on flexible brake line. Remove the jounce bumpers, located in a coil spring. Not to be reused jounce bumper. Drill a hole in the center of the lower spring seat for overhead line pass through a 3/8. Figure "C".
Step 3 – install air Spring
Deflate the spring air coil-Rite and place it inside the coil spring with air, fit down. Then place the upper support at the top of the Coil-Rite (figure & "A" "B"). Cut row air into equal lengths, making sure the ends are cut as straight as soon as possible ("cutting" motion with a razor blade is preferred). The route of the line through the hole in the lower spring seat and along the axis. Insert one end of a line in Setup on the air in the spring.
Step 4-reinstall coil spring
Reinstall the coil spring with coil-Rite on the vehicle. Pass line excess air through holes drilled in the lower spring seat. Attach the lower shock absorber bolt and tighten on the specifications of manufacturers. Figure D. See heat shield notice to install thermal shield. For installation on the right side of the repeat steps 2-5.
Step 5 – set inflation valves
Select the location to mount the inflation valve, this must be a protected area as a rear bumper. Drill two holes 5/16 and go through valves and tighten the nuts. Figure F.
Step 6--routing overhead line
Air line route from air springs inflation valves (figure e). In order to avoid any sharp edges or hot surfaces, as well as the sharp corners. Overhead line can be achieved with nylon ties. Cut off any excess air lines using the method described above and push the end as far as possible in the inflation valve.
Step 7 – inflate and testing
Inflate the air springs with the recommended maximum working pressure (see page 1 for working pressure). With SOAP and water solution to check the air leaks around the valves and valve core. Inflate and deflate in small increments to find the perfect riding conditions for your car.
Step 8-complete
Raise the vehicle, remove the Jack stands and reduce vehicle on Earth. Reattach the battery cable.

Source

Refer to the approved equipment to repair collision caution alerts and notifications. Before starting repair, refer to the metal Panel bonding adhesive applicator for proper preparation and general information.

Edelbrock performer manifold # 2146 & # 2515 consumption will work with 400, 430 and 455 c.i.d. big block Buick engines. Singer # 2146 is intended for placement of the source of cold air induction hood,

1. improve and maintain a safe, comfortable working height. Let the front suspension hanging freely.
2. remove the coil springs, shock absorbers and bump stop. Refer to the service factory for appropriate disassembly procedure.

Functions of the radio:
• How to get to the XM band
-Select the XM1 XM2 or group button
• Tuning in to XM channels
-Scroll through XM channels with Melody pen
-When changing channels radio will display number/channel name, and then restore the default display
– Click to apply for once to select the next channel or press and hold 2 seconds to scan through all

• Egr system: this variety will take stock of equipment EGR (exhaust gas recirculation). On some 1972, and later model cars and only in some States, EGR systems are used. Check your local laws for requirements. Not legal in California on motor vehicles under the control of pollution.
• Diversity: this diversity will not take any rest carburettor system. We recommend the use of carburettors, listed

Buick V6 was 11: 1 compression, high energy ignition and turns 5000 RPM. Taking into account the specifications you'll need to retard the timing for high compression, low rpm and high energy ignition. Comparing the characteristics of the engine against the chart, you can find the benchmark time use. Engines with a combination of elements from both columns will take time, which is set in the middle of the range.

Read all instructions before you begin. This kit is designed to connect to the DynoMax Blackjack painted/cyclone ceramics coated or competitive brand, full length headers.
1.703828 hanger Bolt adapter plates 703825 and 159496 using 5 / 1 6 "-18thd x g/4" bolts and nuts. See system diagram for identification details. The plate will allow 2d / 2 "size saddle clamps are connected with hangers.

Firstly you need to measure and cut the handle threaded rod. Make sure that you allow rod to pass through your collected door, frame and leather interior group and that it has a sufficient number of threads attach internal handle as shown. Look at each image that you must close the door latch system, when the handle is turned off. For the example shown, we used a 1/16 "to 1/32" brass stock that was Threaded with 0000 90 touch and with 0000-90 nut. The length of the clip frame latches will vary from car to car. Also note below that the holes in the doors may require reorientation. We recommend filling the original

This installation guide is designed to complement the instructions to install the BMW to help you with installing Sirius receiver BMW X 5 (E53) with navigation. I chose Terk SIR3 low profile magnetic mount antenna and mounted in the spoiler. As a result of this tutorial will not cover the installation of antennas Sirius BMW and you must follow instructions, along with Sirius satellite antenna Kit BMW

D110.For the BMW E39 5 series M5 ' 97-' 03 – standard audio cable
We are going to proceed as follows:
-Accommodation factory amplifier
-Mounting on new amplifier
-Power connections for the new amplifier
-Audio inputs for the new amplifier
-Join a new amplifier new subwoofer enclosure
-Installation of the new enclosure subwoofer
Tuning/testing new amplifier

There are some steps to update the radio at the BMW E34:
I. in this update we consider shortcomings of the bass factory
and underpowered factory amp. Exchange systems are not equipped with subwoofers. Thus first investments better add to the existing system. To add a subwoofer for the plant systems we need an amplifier to power it. We have several choic-es here, depending on the budget.

Unit is designed to ensure the integration of your car in to a mobile phone and Bluetooth ® enabled mobile phone. This kit is designed to provide Bluetooth in your car quickly and easily! Just find your phone in your car connector, plug the unit into the slot in the MIC if your vehicle is not yet one and your done!
This kit provides integration with the stereo switch off the radio and use built-in BMW

BMW fast start installation (dual-connected and managers-stock ignition advance, 1981-1995 model years with electronic ignition systems factory, see the complete guide installation troubleshooting &).
1. open the "black box" (part 1), set the dip switch according to the sticker (part # 10). Apply a sticker up.
2. fasten the black box (part 1) for the aluminum plate (part 5) with bolts, washers (part # 11).

KIT COMPONENTS
• Housing • Radio Radio trim plates • brackets clips Panel PC-7503 • (4)
• (8) PFH-12 mm flush mount ISO screws • (2) the MBM-12 Phillips screws
95-9307B BMW 5 SERIES DASH SHOWDOWN 1997-2003
1. disconnect the negative battery terminal to prevent accidental short circuits.
2. delete the volume by dragging to the rear of the vehicle.

CAN bus owners to install fuse block with the ignition switch moved to simplify installation and maintenance of all electrical accessories. Hyper-Lites and other accessories may be installed in fuse block without interference from the can bus system.

Warning: this product should only be performed by an experienced welder!Installation:
Note: refer to figures A-E for reference before you begin installing braces-side airport loading/unloading and return the data during the installation process.
The figure shows the finished installation bracket CC products/San Jose BMW Airhead side for general reference.
Figure b shows the upper end of the brace Airhead side where it attaches to the frame
(Note: leave at least 1/2 "intervals below at the bottom of the fuel tank).
Figure c shows how the side brace airfield embarkation/disembarkation should be removed from the tube air inlet.
(D) while the illustration shows how the bottom edge (beveled end) fits frame at the rear of the bike.
Figure e shows one threaded cones properly welded to the frame and painted.

Installation steps:
1. ensure airport loading/unloading side braces fully assembled (threaded cones, firmly screwed in braces on both ends).
2. Holding the airfield embarkation/disembarkation side brace in their proper position (figures A-D) to note the location where you want to weld the front and rear threaded cones to the frame.
Note: the lower (rear) Airhead side brace was canted, for reference.
Note: make sure that the left and right airfield embarkation/disembarkation side braces are located in the same way.
3. Select a frame and remove paint in relevant areas, using Emery cloth for the preparation of the surface of the frame for welding.
Note: dimensions and Mark twice, weld once!
4. keep collected airfield embarkation/disembarkation side braces in their respective positions and tactics to Weld the top and bottom. Perform this step to the top (front) and lower (rear) end of the airfield embarkation/disembarkation side brackets on both sides of the bike.
5. Using removable tape, mark each brace side airfield embarkation/disembarkation or "left" or "right" to make sure they are replaced with the corresponding side of the bike after disassembly.
6. remove the screws and braces side airfield embarkation/disembarkation of welded tactics, threaded cones. Complete welding threaded SAE motorcycle frame on all four points.
7. clear or delete any weld splatter or paint to protect screw Cone and frame corrosion (see Figure E).
8. Peremontaž airport loading/unloading side braces for threaded cones, preserving its original orientation left side/right side.
Note: the lower (rear) Airhead side brace was canted, for reference.
9. torque hex bolts 7 foot/pounds.

Source: http://www.sjbmw.com/_documents/instructions/319_part.pdf

Flat head screwdrivers and Phillips head screwdriver or T20 torx driver T15 and only the elements necessary to complete this installation. Also expired credit card or similar (see step 1) is not required. Note that this setting is made on the E90 LCI. Installation is similar to vehicles, non-DEVELOPMENTAL, depending on whether you have a button bar for the heated seats,

THESE STEPS MUST BE PERFORMED IN THE FOLLOWING ORDER:
1. place motorcycle on his centerstand on level ground and lift the front seat. Remove the screws (2), which took a back seat in place with a 5 mm Allen key. Remove the seat and set it aside.

While simple in principle produce S-Flo to 2.7 l twin turbo very specific increases in engine power and smoothness. The improvements are from a combination of air filter design (unique venturi-shaped base of ITG filter) and the precise mandrel bent transition tube. Our scanning tool measurements recorded an average increase of 25 grams per second of air through the mass air flow sensor (MAF), with a dramatically smoother flow path.

When servicing accessory drive system, it is very important to change the skewer and drive belt. With SKF, you get a belt, which is the same length as OE (Selenium is sold separately), which reduces the risk of breaking further down the road. Skewer (VKM 31034) contains two parts – an idler plastic and a spring mounted

Bi-Pipe installation Audi S4procedures for:
1. Allow the engine to cool before you begin the installation.
2. Remote throttle body coverage by twisting two ¼ turn mounting screws and pull straight up on the front.

Tools we recommend include: Bentley Publishers Audi TT Service Manual (book or CD), torque wrench (3/8, 5? drive recommended), floor Jacks (2 minimum), Jack stands (3 minimum), the tool set including wrenches/ratchet/extensions/metric sockets (various lengths)/hex bit sockets/torx drivers/Allen wrenches (hex key), Wheel wedges (2), small clamps and a digital camera to document your progress in case you need to go back and reviewhow it was installed originally.

The engine control unit has an on-board diagnostic capacity. Before carrying out repairs and debt to find guilt must be questioned memory. Vacuum hoses and connections must also be checked (unmetered air).
-Fuel hoses in the engine compartment shall be ensured only with spring-type clip. Clamping devices-type or screw-type clips may not be used.
-A voltage of not less than 11.5 v is necessary for the proper operation of the electrical components.

Dension Gateway five you can connect your iPod or USB storage (stick, hard disk or storage devices capable MP3 player) to your original car radio, provides playback of music, menu-based controls and collection.
Gateway five also offers Bluetooth connectivity for music streaming (via A2DP) and hands-free mobile calls handling via the original buttons and screen shots of the car.
Connections
Turn on your car stereo and select

Preparation of the vehicle, you can either put the car on ramps or you can place it on the jack-stands and remove the front wheel. Make sure that you order the correct generator with the correct amperage. You can wait for your new generator, until you see what an old look. Mine was 120A. Be sure to have your defective generator is tested to ensure that this is the part fails. You can be sure when you order a new generator that you get with the friction disc is guaranteed already installed. I tried to buy an auto parts store and AutoLite from disc from the old generator would not work at AutoLite. I think this is the same for some Bosch and. I think friction disc are secured configuration varies. You can also replace v belt when you get it for this repair anyway. You can also replace your power steering fluid, when you are finished with the repair, then you should do this regularly anyway.
Remember to carry out any unnecessary dismantling.
Step 1: REMOVE UNNECESSARY HARDWARE
Remove plastic skid plate at the bottom of the engine compartment. Remove the plastic cover from within the engine compartment. This includes the removable robust stripping, hood and engine room. Remove the cover, which is against the firewall, which houses the battery. Remove cover from power steering fluid reservoir.
Step 2: DISCONNECT BATTERY
Be sure to use caution.
Step 3: REMOVE the FRONT BUMPER ASSEMBLY
Remove the inside wheel wells. They are kept around 14 different bolts. Remove black housings that covers the area where the fog lights. They are simply cropped in and requires some drag to remove. Disconnect rear fog light electrical connections for each fog light from under the car. Remove the 2 bolts (1 on each side) in the car where two metal pieces Join in support. Disconnect the front bumper wiper spray electrical connection for each the wiper motor. Interrupt line spray on the driver page. There is a plastic art, to be removed carefully so that the line simply subtracts from each other. Use a baggie and zip tie to secure the end of the line from reservoir to control losses of Wiper fluid.

Source

To service requests from LEDs while the comes with their operating voltage and are not covered by their respective filters or diffuser screens, the following instructions are complied with:
1. Repairs and operation of the control can be implemented with protection glasses only.

Kit Contents: 1. DICE module 2. Audi radio interface cable (vehicle-specific cable) 3. Docking cable
Installation steps for this kit
1. Drag the vehicle in-service bay and access trunk area.
2. Disconnect both battery terminals. These cables must be disconnected during installation to assure correct initialization of module DICE when the DICE when it is connected.
3. remote radio by inserting keys (4) plant (not included)

Installation for 2001-2003 Eulogize 3.2 CL Cold Air System:
1) getting started
(a)) makes sure that the vehicle is parked on a plane surface.
(b)) set the parking brake.
c) disconnect the negative battery terminal.
(d)) If the engine has run within the last two hours it Let cool down.

2) Remove Stock

Because this is a "Race only" product, it will not meet emissions standards. As it is a "Race only" product, it will also lead to "Check Engine" light will be illuminated after three complete driving cycles. This is not a problem for maximum performance. "Check engine" light will not cause the engine computer to go into a "safe mode". It is only a system function indicator. MAKE special note about dealing with your Jackson Racing stainless steel header: congratulations on your purchase of Jackson Racing header stainless steel. This is the finest letterhead on the market today. It is constructed from 100% stainless steel. Including flanges. It will not rust! But special care must be taken during installation and handling of stainless steel to the tubing to always look good.

The Interior ventilation filter to Eulogize RDX, TL, TSX, Honda Accord, Civic, CR-V. Inside ventilation filter is located in the filter housing behind the glove compartment door.
1. open the glove box door. Understand and drag down on glove door holding rod placed on the right side of the glove box door.

This square provides the solution for installing a K20A (ITR/CTR/Euro R) cable actuated throttle body in a K-Powered EG, EK, DC2 or EF simultaneously:
-Enable the use of a card OEM throttle cable (Eulogize 17910-ST7-L01) for swap cleanliness

This B and M Precision Sport Shifter is designed to work on most 2002 + Eulogize RSX/Honda Integra (including 6-spd Type-S) and 2001 + Honda Civic models equipped with a manual transmission. It has been designed to reduce the significant shift throw and improve Symbol switching sensor. Check lists parts and tools at the beginning of

Read and understand these instructions before you try to install this product.
1) getting started
(a)) makes sure that the vehicle is parked on a plane surface.
(b)) set the parking brake.
c) disconnect the negative battery terminal.
(d)) If the engine has run within the last two hours it Let cool down.

2) Remove Stock provisioning system
(a)) remove the stock air box Assembly and attach the hardware from inside the fender well.
(b))

Thank you for buying system Comptech stainless exhaust to Eulogize NSX (1991-2006). All components have been designed and manufactured using the latest technology and materials. Please take a moment to read this instruction manual and warranty information page carefully before you start any work. Always work in a clean environment and use appropriate safety equipment and tools to avoid potential damage or injuries. Comptech recommends the use of a true two-door sports Service Handbook to supplement those instructions. All Comptech products is intended to

(A) the revised timing belt skewer for 2002-2003 Eulogize 3.2 l engines are part of a product improvement of Eulogize. The original design timing belt skewer is filled with oil damping oscillation. Due to a manufacturing situation can skewer the oil leak. If enough oil is lost, timing belt loosens and causing engine noise. The worst-case scenario is selenium may lose tension and allow losses to the cam timing. Vehicles with the revised skewer should be identified by a guillotined mark above the sixth digit in the engine

General remarks
"I have no 3002 3.2 TL - S and love every aspect completely. I had a 1999 32. TL before and neither car has ever
had any kind of Squeak, rattle or defective. Quality and performance for the money are Cavalry veterans. I also have a 1999

Additional parts Loosen needed when you have a Dragon Filter, 1 x 3, 5?-03? plug/2 x 3, 5? Clamp remove bolts securing OEM air cleaner box, clamps on OEM rubber intake manifold. Remove the coolant transfer/PCV ruthless from from OEM intake and engine. Mark coolant transfer hose origins, install the 10 mm tubing is supplied in the kit to these 2 sites. Remote OEM rubber intake tube, Remote box OEM air cleaner by pulling upward.

Below are brief explanations of the items on the Service maintenance plan. Only a qualified technician should perform work at the same time, in accordance with the procedures laid down in the new Range Rover Workshop Manual. Always use proper methods, tools, equipment and safety rules. Some additional details and specifications are provided in the instruction manual or Workshop manuals.

The customer may appeal of binding, improperly stored, noise when seats are stowed or other operational problems with the third row of seats.
Resolution: ADJUST or repair the component SEAT causing the problem
Several areas have been identified as a contribution to the operational difficulties with third row of seats. When a customer complaint has been verified and diagnosed, follow applicable repair process.

Camshaft timing belt be replaced if the cylinder head is to be removed, or if the drive gears, skewer or coolant pump must be replaced. Camshaft Timing Belts must be stored and handled with care. Always save a camshaft timing belt on its edge with a bend radius greater than 2.0 5? (50 mm). Do not use a camshaft timing belt, twisted or bent double, as this will damage the reinforcing fibers. Do not use a camshaft timing belt, if debris other than belt dust found in the timing belt cover.

These instructions guide for filling Ihe seat device and safety belts listed as separate operations. It is recommended that the installation completed in this order. Under no circumstances should this seat or any par in this kit is installed in a vehicle without Safari cage "D-pitlar" and horizontal rails mounted – also for inmate safety, no person shall ride in behind any Defender 90 vehicle without a properly installed rear seat belts and Safari bur. any person Riding in the back of a

The primary reason for the selection of Prima engine for duty in your Land Rover is fuel economy. Montego is known to be thrifty, 55 mpg average is common, but its also one of the least expensive motors to buy at the moment due to 10 plus years old cars lack their MOTs. Prima is also fairly well known for a long service life, as well as its e? efficiency, and it is a high-reving diesel oil with very similar power delivery to the Land Rover petrol engine. It is not unusual to pay $ 50-$ 150 for a car with a good engine, in fact, many people are given carsm. They have an edge over a lot of the other options. Engine fails? t on the Land Rover gearboxes, so an adapter plate is necessary for

The VEHICLE can not CRANK after being UNLOCKED the customer may appeal to the occasional vehicle will not crank. This may be due to the non-NAS Passive Immobilization been inadvertently turned off in production or during repair operations.
If Passive Immobilization is enabled, the vehicle locks even if the ignition key is turned to place "II" or the engine does not start within 30 seconds of emancipation of the vehicle. With the ignition key in position "II", will the vehicle shows that it is in portrait mode by emitting the alarm LED continuously. Engine won't crank if the ignition key is turned in an attempt to start the engine.

Microcat can be installed to operate in a standalone or network environment. Installations of Microcat requires a dongle (hardware security key) to be connected to the appropriate computer port. If a dongle is not connected to you may be required to select your region and country.
Microcat authorization Server (MAS ™) can

The purpose of this amendment is to allow the MOBI-ARC PWM regulator to control builder. Read through these pages before undertaking change. People are not mechanically inclined can choose to get local Builder re-builder to facilitate this change.
In its original configuration using this generator diodes in rectifier plate known as the "avalanche" diodes. Avalanche diodes are fine for charging, but they are incompatible for welding due to their limited breakdown voltage rating. In order to use the

1. disconnect the negative battery cable. Remove right side engine under cover pages. Remove the power steering and a/c Compressor drive Belts. 2. remove the a/c compressor and power steering pump with hoses attached, and secure way. Support engine from above or with the word jack during the oil pan. Remove the air cleaner case with air cleaner outlet hose. 3. remove the engine mount and mounting bracket from timing belt exit of the engine. Loosen the water pump friction disc is guaranteed bolts. Remove the water pump drive belt and friction disc is guaranteed. 4. Remove 5 crankshaft friction

Rear lowering Kit Installation: 1. remove the plate on the bike so it can put on a lift. Ensure a motorcycle to motorcycle lift and lift the rear wheel motorcycle, so is un-weighted. 2. Remove cover in front of elevator skaktens drive. Remove the regulator/rectifier. This can be disconnected during this procedure. 3. Next remove bolt holding shock spring into the suspension and then the two bolts connecting material support arm (material support arm lowering kitlooks just like our own, but is slightly shorter). 4. install your new lowering arms, leaving a little slack in the screws. Install shock spring back to

CT exhaust system Series Installation: step 1: CHECK the package contents: 1. four (4) Header Mount flanges 2. Four (4) spinning noses 3. One (1) the right and one (1) the left Page Header (primary colors) 4. One Collector 5. Package containing Springs, spring puller and supplementary information 6. One (1) of the elbow (or two (2) If dual) 7. One (1) CT muffler (or two (2) If dual) 8. One black rubber cap. Step 2: PRE-ASSEMBLE HEADERS, COLLECTOR, and MID-PIPE to assure proper fit between all parts: Brocks performance pre-assembles exhaust system before it is delivered to your door.

Exhaust systems Installation: step 1: CHECK the package contents: 1. four (4) Header Mount flanges 2. Four (4) spinning noses 3. One (1) the right and one (1) the left Page Header (primary colors) 4. One Collector 5. Package containing Springs, spring puller and supplementary information 6. One (1) of the elbow (or two (2) If dual) 7. One (1) CT muffler (or two (2) If dual) 8. One black rubber Cap (not shown) step 2: PRE-ASSEMBLE HEADERS, COLLECTOR, and MID-PIPE to assure proper fit between all parts: Brocks performance exhaust system pre-boot assembles before it is delivered to your door.

Free PDF download for 1999-2001 Suzuki GSXR 1300 Hayabusa Power Commander 2 Installation Manual. PDF Online Suzuki GSXR 1300 Hayabusa motorcycle spare parts, repair, installation, removal, workshop, maintenance, owners manual.
Power Commander 2 Installation: 1) to remove the passenger seat or solo seat cover section. 2) remove the seat. 3) Feed pipes Power Commander II from the rear over fender Assembly and under the tail section and subframe. 4) Disconnect the left connector equipment ECU (Figure A). 5) set of male plug from the Power Commander II in stock ECU. 6)

Rear Fender front/Installation: 1. covers area of fender, where Fender Tip goes with a thin layer of masking tape. Make the tape is smooth. 2. carefully position front Fender Tip on fender, make sure the tip is centered on the fender. 3. Select the hole locations with marking pen. 4. remove the Fender Tips. 5. drill holes through the fender on the brands. 6. remove the masking tape. 7. place the Fender Tips and insert the screws from the

Exhaust system Installation: Remove your STOCK SYSTEM: 1. place the appliance on a stable work tripod. 2. If you are not familiar with the remove refer the original exhaust gas to the owner's manual before you begin work. 3. Always allow your computer to cool down before you try to remove exhaust gases. 4. remove the two bolts from the right side. Then remove the side panel. 5. Loosen the stock mid-pipe clamp and then remove the stand-off bolt and bracket bolt, which supports the muffler. 6. remove the stock muffler and mute stock solution main pipe. 7. Slightly loosen the inventory

Free PDF download of 2006 Suzuki LTR450 fuel management interface the IMF in the Installation Manual. PDF Online Suzuki LTR450 motorcycle spare parts, repair, installation, removal, workshop, maintenance, owners manual.
Installation of the IMF in the fuel management Interface: 1. remove the seat. 2. remove the plastic clips that hold plastic gas tank cover on the left and right side. 3. remove gas cap and gas tank cover (replacing the gas cap, as soon as the gas tank cover is removed). 4. Mount Motoworks IMF to plastic underneath the seat by means of Velcro.

Drop Exhaust System -on Installation: 1. make sure that the bike is completely cold before you start the installation. Make sure that the bike is sure hand position or ideal rear service position. 2. remove the original muffler is careful not to damage exhaust gasketit. If you damage the gasket can you get a new one from your local Suzuki dealer. In most cases, you can reuse the original gasket. 3. install the black "Y" left parenthesis as shown by removing behind allen appendage from passenger footrest and replace it with the supplied 8 mm x 55 mm allen bolt on. Securely tighten the 8 mm x 55 mm allen bolt on.

Rear lowering Kit Installation: 1. determine how much you would like to reduce your motorcycle. Refer to reference the chart at the bottom of this page to determine the correct installation location holes to drop you want to achieve. 2. Ensure a motorcycle bike lift and lift the rear wheel motorcycle, so is unweighted. 3. Loosen and remove the two self-locking nuts, and flat washers from connecting arm bolts from the left side of the vehicle. 4. slide the connecting arm bolts from the right side of the motorcycle (it is necessary to push bushing back to the left side to allow the bolt head to drop below budget.

SpeedoHealer Installation : 1. remove the left foot peg by removing the two 14 mm bolts securing to the motorcycle frame. 2. Next remove 10 mm bolt Breaks the selector on the farm. (Note: you may wish to select levers position in relation to the gear shaft to aid in the correct location during reassembly). 3. remove the four 5 mm Allen bolts holding on the left side cover. 4. When the cover is

Electronic Jet Kit Installation: 1. before you install TFI you must first disconnect the negative lead from the battery. 2. location of TFI Determinea specified volume of a unit. Suggested locations areas follows: Under the seat, behinda side door or tail section. 3. TFIcomeswitha wiring harness with injector connectors that corresponds to the factory injector connector. 4. Locate the factory fuel fuel injectors (see owners

Installation instructions: make sure that the bike is completely cold before you start the installation. Make sure that the bike is sure hand position or ideal lift service. Remove right side lower wind screen to postpone the muffler Assembly. Remove the four fasteners on the right side cover. Loosen the muffler clamp attachment OEM muffler to head pipe. Remove two muffler mounting bolts and remove OEM muffler.

Adjustable foot control installation: 1) to continue to the right side of the vehicle. Remove the line stock brake from the brake master cylinder rear and rear brake caliper. 2) remove the clevis pin attached to the brake lever rear brake master cylinder. 3) remove the rear brake master cylinder and let hang free. 4) Disconnect the rear brakes light from wires and remove the right foot control Assembly. 5) Mount collection right foot control is supplied in the kit to the frame with the stock screws. 6) Mount rear brake master cylinder to the foot control using the stock fasteners to be removed.

Contents: General information, intermittently fuel system, maintenance, cooling system, engine TopEnd, clutch, the engine lubrication system, the engine removal/Installation in the crankshaft/transmission, wheels/tires, Final drives, brakes, Suspension, steering, frame, electrical System.
1. Crankcase emission control system, this system eliminates the release of crankcase vapors into the atmosphere. Instead be routed by the vapors through an oil separator to the inlet side of the engine. While the engine is operating, be signed by vapors in the combustion chamber, where they burned with the fuel and air is supplied by fuel injection system. 2. Exhaust emission control system, this system reduces the amount of pollutants released into the atmosphere of

1. some pictures in this section is used to illustrate examples only. It is up to you how you decide to cut your bodywork motorbikes frame slider to accept there are many different ways customers go through this process. Shogun is not liable for any part of your motorcycle action. Just measuring the location of the cut and if in doubt at any time please call us before the install process is started. Professional installation is

1. Assure and exhaust components is fully COOLED. 2. ASSURE MOTORCYCLE is STABLE on STANDS or a REAR CENTER POSITION or SERVICE TABLE. 3. remove the PLASTIC COVER OVER 3 PLASTIC BUTTONS HOLDING the EXHAUST SERVO. (THIS IS LOCATED DIRECTLY INSIDE THE RIGHT REAR PASSENGER PEG BRACKET). 4. DISCONNECT the CABLE END FROM SERVO WHEEL and REMOVE the ENTIRE CABLE FROM RESTRAINT

Note: remove the negative cable from the battery before you install this accessory. Composing the excess off wire ties after attaching them to wire the stomach bags. Do not allow the cut part of the wire tie to interfere with another wires or brake hoses. Be sure to observe all safety notes and precautions that are described in the service manual while fuel tankremoval and installation of. Gasoline is extremely

1. remove the seat from your motorcycle, remove the 2 screws in the middle of your space. There is one screw on each side. If there has never been a sissy bar installed on your bike, it may be necessary to drill holes in the fender to mount the sissy bar in space provided by Honda. Hear your maintenance manual for more information regarding this procedure. 2. attach the mounting rails to each side of the Panel

1. the installer of the lift at the rear of the bike over the floor, 6.35-8, 5? clearance between floor and rear wheel the bottom of is recommended. If a frame type Elevator is not available, an automotive type screw jack or hydraulic floor jack can be used in conjunction with a 24? long 2, 5? x 4 5? by 2, 5? x 4 5? turned across the rear tire, before lifting towards the bottom of the swingarm. Lift the bike well above 8, 5?, and Insert a

1. find a motorcycle for a Punch mark as described in the identification on page 2. If a Punch mark is no longer current action is required, return the unit to the customer. 2. classify the device/client as follows: • Ice tire in the motorcycle the original factory-installed tire? • Air pressure Ice loss more than three psi per month? Note: see page 145 in the instruction manual. "Even tyres are in good condition can lose one to two

1. some pictures in this section is used to illustrate examples only. It is up to you how you decide to cut your bodywork motorbikes frame slider to accept there are many different ways customers go through this process. Shogun is not liable for any part of your motorcycle action. Just measuring the location of the cut and if in doubt at any time please call us before the install process is started. Professional installation is

TURN SIGNAL MOVEMENT 1. Refer to figure 2. Remove the seat. Security: DISCONNECT the BATTERY BEFORE ALL WIRING CHANGES 2. Disconnect the cables turn signals to and taillights below the seat. 3. remove the three bolts on each side, which ensures the fender to support striving for. 4. Lower fender onto tired and remote. 5 turn signals . remove from fender strut. Observe and marks "left" and "right" for reinstallation.

While completing this procedure, be careful not to damage the covers, cowls or other components. 1. remove the intake air support (page 3-8). 2. remove the upper inner cover. 3. remove the lower cowl. 4. remove the right cowl Center. 5. remove the right crankcase cover (page 10-5). Clutch removal. 6. Remove the starter idle gear and shaft. 7. remove the snap ring and stopper ring. 8. Remove the coupling lifts piece and plate.

1. Provide assistance/clarification to the lift installer. 2. Avoid causing injury installer, customer, end user or others. 3. Avoid damage to the motorcycle and/or accessories. 4. Avoid death to customer or any other vehicle operators. Installer: Please forward this sheet to the customer after the review of the 5. It is almost impossible for us to be able to solve all possible situation a Setup program or the user will encounter.

Assembly instructions: do not exceed these values when installing rack, otherwise damage to Main Arm can occur torque. When the stock mounting points are used to mount the rack motorcycle, refer to motorcycle owner's manual for recommended torque values. Johnny Rack is not responsible for damage caused by the fitting of this rack motorcycle. Please be advised that, although smaller, motorcycle powder coat damage may result. If this is unacceptable, you must not install this rack. Protective sleeves are supplied, but they do not guarantee protection against powder coat damage. Further measures should be taken to prevent damage to your powder coat, e.g. protective sheeting resemble the invisible car bras.

Assembly: Assembly parts, as shown below with the main fittings in the bottom turn signal and then bracket, and then the tail light left parenthesis. Screw them together with the specified button head allen screws and nylon insert lock nuts. Insert screws through the bottom and attach nuts on top of the Stillingsgruppe to maintain a clean appearance from the bottom of a left parenthesis.

Installation instructions: • use the stock rear hinge mount. Hinge bushings must have their faces being thinned by. 05.35 each for the tank to fit on the bike. DO NOT BEND aluminium bracket wider! • You can adjust the CAP lock tension, use silver button head cap screw on the bottom of the common agricultural policy. Tighten the screw to tighten the latching, Loosening will loosen the stores. Common agricultural

1. Remove the following wind screen components per the instructions in the manual, Ducati owners: • Instrument surrounds • projection windscreen • Chin wind screen (under the projection/air intakes) • right Middle wind screen (covers battery) 2. Disconnect the speedometer cable from the speedometer. Unthread ring nut at the top of the speedometer cable and drag back cable down approximately 4-6 inches. 3. Disconnect the projection lines from the point of contact the bulbs. Pull back the rubber boots projection Assembly back in to get access to wire the terminals. Note that two ¼

1 speed Sensor . connect the clutch. Switch the instrument to DC 20V position. Connect the negative terminal of the battery black meter probe. Turn the ignition on. 2. in Signal wire initially identify out of the 3 wires. Connect the Red meter probe to one lead in 3 p plug through the back, using a thin needle for back-testing. Rotate the rear wheel in his hand. Signal wire is where the level voltage

Signal wire 1. Clips about 5 cm (2.35) away from the sensor connector. Catch the end of the wire that goes to the sensor and deprive from approximately 1 cm (0.4 5?) insulation. Splice White SH wire to this point, and isolate the delivered or electrical tapeshrink tubes. 2. Similarly, splice Green SH wire to the other wire end of the signal cable. 3. Splice black SH wire rope speed Sensorto Earth, or

Preparation: – the ignition key should be in the OFF position. — The rear wheel Travel from the Earth by using a tripod. Make sure the rear wheel tours for free. – Remove the seat. Speed Sensor are usually placed at the top or side of the gearbox and reads the revolution of the opposite. 3 speed sensor -Pole plug either connects directly to the sensor or located 10-30 cm (4.35-12.35) away from the sensor.

INSTALLATION of the CONTROL DEVICE THE CRUISE • remove cap screws from the clutch master cylinder mounting clamp on the handlebar (LHS); • Remove the clamp bracket from fork and use a file grinder or sandpaper on a flat surface, remove material, equivalent to about ½ switch mounting bracket thickness from bottom face of the clamp. • Insert two cap screws to clamp and the switch bracket with hardware on the bottom screw; • Unscrew the cap screws in the master cylinder by using a 5 mm hex key and position the master cylinder to ensure that the switch left parentheses

1. make sure that the bike is completely cold before you start the installation. Make sure that the bike is sure a center position or ideal lift service. 2. remove OEM drop-on tubes with mufflers: – remove spring connections. -Remove both the muffler clamps. – Remove the muffler joint bolts. -Eject OEM drop on pipes and mufflers. 3. install the two brothers Racing v.a. l. E-drop-on system: – attaches

1) Lift the rear section. 2) removing the left hand side wind screen. 3) Find the plug, residing in between two throttle bodies. This plug has a round silver preserve ring at the end of it. 4) Screw this connector by turning it counterclockwise. 5) Note: you can route cables from PCIII from the tail to this area before connecting it. This will make for a cleaner installation. Insert the female plug wiringfrom PCIII in. 6) Plug male connector from PCIII in the female connector on a left parenthesis. 7) Route cables along the frame to the rear of the bike. Make sure the wires are routed so that they do not get caught. 8) Attach the Earth wire from PCIII to front, left hand, the mounting point of the ECU. 9) Attach PCIII at the top of the ECU using the supplied Velcro fastening. 10) reinstall the left hand side wind screen.
Download Complete the 1998-2001 Power Commander Ducati 996 III Installation Manual.

This is the beginning of a modern age of head-turning style, essential technology, exciting performance and handling, uncompromising security and an advanced fuel efficiency. These values constitute the, Kia's vision of the future. And from the moment you see the all-new Kia Spectra, you know the future definitely looks good.
Stylish appearance is much more than skin deep in the all-new Spectra. At first glance, makes the all-new Spectra a

There are plenty of vehicles to choose from in this competitive market segment. Some vehicles in this class has been on sale for a long time. and are from established manufacturers that incorporate excellent value in their cars. This new vehicle from Kia is also excellent value. Its avid drives away pricing will win lots of fans but more important in
Spectra adds a new fresh design to blend. It is a comfortable, easy to drive vehicle must be included to the shopping list of buyers looking at cars in this category.
Spectra are sold with an extensive list of standard features especially for new vehicles in this class. Spectra comes standard with air conditioning, electric

Document here is the owner's Manual of the KIA Soul model year 2011. This manual contains all information about the vehicle from the service maintenance, vehicle specifications, safety information, vehicle maintenance, etc. KIA offers a wide range of settings, components and features to its various models. Therefore some of the equipment described in this manual, together with the various

KIA Rio manual Sedan – car Review. Review of KIA Rio Manual Sedan, containing about: car pricing, standard feartures, design and function, safety, security, performance, handling and management, etc. Kia's all new JB series Rio replaces the previous model chunky silhouette, with a slimmer, healthier style. Under the hood a 1.6 litre engine gives featuring variable valve timing, an extra 8kW, while a 90 mm longer wheelbase adding interior spaces. Hatchback versions are shorter than the old series, but sedan grown 25 mm in length. There are significant improvements in build quality, and Kia's "drive away" pricing will give extra appeal in this cost-conscious end of the market.
All new Rio brings with it significant improvements in quality, safety and performance. Its list of standard features confirms how competitve is class small car. And it is good for the consumer. But what the newcomer is missing is coherent and pleasant handling of some of the opposition.

Optima is Kia's first run on class medium-sized, and while it cannot be on the same level as the Honda Accord and Toyota Camry, it has most of the right stuff to compete. For 2005, receive this Hyundai Sonata clone only minor updates, including clear turn signals and updated leather seats. The Standard engine is a 2.4-litre common rail four-cylinder unit makes 138 hp. an optional 170-hp, 2.7-liter V-6 is also available. Four-cylinder is provided with a Sportmatic automatic transmission. Optima comes in two trim levels: LX and ex. LX few standard power windows, cd player,

KIA Timing Belt Installation and removal. This document contains parts of information about the Service Manual and electrical diagrams showing you on timing belt installation and removal of KIA with 2.0 common rail engine (including DTC). This installation removal includes illustration and text tutorial. Use this installation manual as a reference guide. With 30 steps of instruction, you can remove and install your own vehicle timing belt.

KIA Spectra manual Sedan – car Review. Review of KIA Spectra Manual Sedan includes car review about vehicle features, pricing, design and function, safet, security, performance, handling and management, etc. Kia Spectra is the new model in the range of Kia. It replaces the previous models; Spectra, Spectra and Mentor. As well as, provide the Kia a fresh modern market participant in the market segment competitive small vehicle, just about every manufacturer has a model on sale. Spectra is available as a four door sedan only at this time, a sporty hatch version expected out later in 2005.

Convert Land Rover for a soft Top. Some people are daunted by the task to remove a Land Rover Tag – this is a big part of the vehicle, after all. Remove Land Rover tag is a simple task, if a bit time consuming, as our step by step guide fitting a soft top shows. This manual uses a 88-inch Series IIA, the fundamental principles apply a utility Land Rover, which will be equipped with a traditional tilt frame and canvas top. Principles of removal is the same, although with a station wagon at the top and a Land Rover Defender truck cab, you may find that you have some interior trim remove first.

This Land Rover workshop manual covers vehicles from the 1996 model year onwards. This Workshop Manual is designed to assist engineers in effective repair, service and maintenance of the Land Rover Defender 300Tdi vehicles. Persons who undertake their own repairs should have some skill and education, and limit repair to components that are not could affect the safety of the vehicle or its passengers. Land Rover Defender 300Tdi

fitting a Noisekiller Soundproofing Kit for a series Land Rover. The engine, gearbox and overdrive creates so much noise, listening to the radio, calling someone on a mobile phone or just a basic conversation with your passenger is almost impossible during driving on the motorway.
To get rid of the noise I decided to look after a killing kit from Noisekiller noise. They do complete easy to suitable DIY kits for all kinds of land Rovers and other vehicles like campers or normal sedan cars. For land Rovers supplying the kits for all types of new and old, front and rear set. Also available under the hood sound noisy and heavy curtains to cover the engine and transmission box. The two kits, I have installed in my series Land Rover is the 109 front cab sets and 109 station wagon rear sets.

2003 Land Rover Discovery electrical circuit diagrams The Power Distribution diagram shows the connections from the battery to the engine and passenger compartment fuse boxes. It also shows the internal circuits of fuseboxes. The document of electrical circuit diagrams, contains all electrical diagram, wiring diagram and wiring color codes apply to the Land Rover Discovery year model 2003. This electrical circuit diagrams,

Land Rover 4.0 and 4.6 L V8 engine overhaul manual. This guide provides procedures for inspection of V8 engine on the bench with the gearbox, clutch, intake system, exhaust manifolds, coolant pump, starter, generator and all other ancillary equipment removed. For more information about general information consult adjustments, removal of oil seals, engine units and auxiliary equipment Repair Manual.
This manual is divided into 3 sections:
• Data, torque and tools
• Description and operation and
• Overhaul

Land Rover R380 gearbox overhaul Manual. This inspection handbook contains procedures for the inspection of the R380 gearbox on the bench with clutch and, if applicable, transfer box removed. All other information relating to adjustments, removal of oil seals, clutch, box and gearbox Transmission device, consult the appropriate Repair Manual for that model. This inspection handbook is divided into 5 sections, Data, torque Tools, settings, Service description and final inspection. This inspection

Land Rover 300 TDi overhaul the engine manual. This engine is equipped with the following models from 1995 onwards: Discovery, Defender, Range Rover Classic. This guide provides procedures for inspection of the engine. All other information relating to adjustments to consult the removal of oil seals and engine Repair Manual for that model. This manual is divided into 3 sections: description, operation, inspection and Data, torque and tools. Servicing operations include reference to the tool Service numbers and the associated artwork depicts the tool. Where usage is not obvious shows the tool in use. Operations also include reference to wear limits, relevant data, torque numbers, specialized information and useful meeting details.

This document is Land Rover internal engine parts fit either petrol or Diesel, except where noted. Here also includes electrical wiring system for Land Rover. This Mitsubishi parts Guide content: internal engine parts, cylinder head parts, lower engine parts, clutch, gearbox – Series IIA, gearboxes, Series III, transfer case, cooling System, fuel system, exhaust System, steering, brakes, drums and friction, braking and clutch hydraulics, Suspension and wheels, front axle, rear axles, chassis components, body components, the Electrical System.

The amount and type of information and tests are available with Land Rover VCS varies from the year, model and equipment settings of the test vehicle. With this software you can: interpret electronic control module trouble codes, read the input and output signals, perform bi-directional tests, test specific systems and components, check whether certain actuators (solenoids, valves and relays) operates, customizing your scan utility function and record and view your movie.

1. place your bike in centre stand. 2. Disassemble the hyphen, starting with the two top føreshus support located on the right and left side of the screen the wind. 3. Next remove two (right and left) dash side panels. It is not necessary to remove seat transition from the left panel. Just hang it over the side of the bike until you are ready to reinstall it. 4. When the side panels are off instrument cluster can be removed by taking out two top mounted socket cap screws (technical name of allen head bolts). When the screws are out carefully tilting instrument panel down to gain access to the

Exhaust gas SYSTEM removal equipment: 1. putting the motorcycle on a page, we recommend a racing stance. Make sure the surface is fast and flat. 2. Remove Rytter seat and electrical coverage. 3. unscrew the bolts, pinch off plastic ties, disconnect the electrical connectors to the rear position lamps and remove passenger handles. 4. unscrew the bolts (a) and remove number plate bracket with signal lamps

Installation instructions • not paint the area where the Petcock o-ring seal or leak will occur. • NOT PAINTING UNDER PETCOCK! • You can adjust the CAP lock tension, use silver button head cap screw on the bottom of the common agricultural policy. Tighten the screw to tighten the latching, Loosening will loosen the stores. Common agricultural policy functions such as vent. • Use the stock Front Mount. • Make sure that the idea is not being rubbed at any time of the frame or other hard surface, puncture from wear can occur. • WARNING; When weight loss is the main goal of FuelCel design and composites not "malleable" like metal, rupture of the fuel tank may occur instead of weakens. • This tank are sold without warranty either expressed or implied by the manufacturer and its final suitability is determined by the operator, motorcycle, where it is installed.
Download Complete the 1998-2000 Aprilia RS 250 fuel tanks -Installation Manual.

1. Insert the graphite gasket in inlet bush by link-pipe and correctly attach the metal clamp on inlet bush of link pipe. Push the link pipe onto stock purchasers. Insert the catalyst in link-pipe. 2. push the muffler onto link-pipe, and attach the springs. Correctly assemble bolt, washer and aluminium distance bushe. Tighten the screws muffler square and metal clamp. The final installation: 1. clean grease stains: a. muffler – Titanium outer sleeve: use a soft cloth sprayed with a spray lubricant multifunctional (WD-40 or the equivalent). b.-carbon fiber outlet Cap: use a soft, dry cloth. c. stainless

INSTALLATION of the additional mounting sets FOR the left MUFFLER: 1. place and install on the lower side head tube for more metal ring (longer bracket for attaching spring) correctly. 2. hand-tighten the bolt of additional metal ring. 3. install additional Graphite plugs into link pipe of the left muffler (NAV-192). 4. coat in bolt and inner side of the metal clamp with Akrapovic anti-seize unleaded copper insert (black tube)

1. make sure that the bike is completely cold before you start the installation. Make sure that the bike is sure hand-stand or ideal rear service position. 2. Unhook the springs, keep stocks smoke grenades to headers. 3. remove the screws that attach the stock footpegs smoke grenades. 4. Take off stock smoke grenades. 5. place a gem of hi-temp sealant sludges on the outside edge of the letterhead, which goes to TBR s-bends. Boost S-bends onto the end of the headers. Leave loose for now. 6. place a gem of hi-temp sealant sludges on the outside edge of the s-bend, passing in the grenades.

ASSEMBLING RIGHT HAND GUARD 1. Lift the protective sleeve (A), release the nut (b) and remove the mirror from his home in block C. Unscrew and remove the bolt (d) and remove the anti-vibration weight e. 2. Perform the following operation with the greatest care and attention in order not to compromise the operation of the braking system. Unscrew and remove the nut (F), holding the brake lever in position. Unscrew and remove the bolt and screw in bolt 1, length 36.5 mm. Tightening torque for bolt 1: 5.1 ftlb (7 Nm). Verify the correct operation of the brake lever and front brake system.

1. Insert the graphite gasket in inlet bush by link-pipe and correctly attach the metal clamp on inlet bush of link pipe. Push the link pipe onto stock purchasers. Insert the catalyst in link-pipe. 2. push the muffler onto link-pipe, and attach the springs. Correctly assemble bolt, washer and aluminium distance bushe. Tighten the screws muffler square and metal clamp. The final installation: 1. clean grease stains: a. muffle

Signal wire 1. Clips about 5 cm (2.35) away from the sensor connector. Catch the end of the wire that goes to the sensor and deprive from approximately 1 cm (0.4 5?) insulation. Splice White SH wire to this point, and isolate the delivered or electrical tapeshrink tubes. 2. Similarly, splice Green SH wire to the other wire signal cablelate. 3. Splice black SH wire rope speed Sensorto Earth, or any other ground wire. 4. Splice red SH cord to the Power wire speed Sensor, or any other fused power lead. 5. Make sure that all connections and insulations are good. 6. connect the 4-pole wires connection to box SH 7. Check if SH is installed and working properly: – have ignition. – Press and hold the SEL depressed while you turn the ignition. [t] (test) is now provided.