Online repair manual

2.8 Liter VR6 2V Fuel Injection & Ignition, Engine Code(s): AFP 24 – Multiport Fuel Injection (MFI) Servicing ignition system => Page 28-1 Note: The Engine Control Module (ECM) has On Board Diagnostic (OBD) capability. Before carrying out troubleshooting and repairs, DTC memory must be checked. Vacuum hoses and connections must also be checked (unmetered air).

After examining the fuel pumps returned under claim for the above vehicles, it has been found that a high percentage of returns have no operating fault found with them. The normal complaint is “not pumping”, or “fuel starvation”. In some cases the fault may be cured when a new fuel pump is fitted, but returns shortly afterwards. There are two common causes of these symptoms on the vehicle, besides the fuel pump: 1) The Rubber Fuel Supply Pipe This may be

Removing Remove cover – 4 – with a screwdriver. Remove screws – 1 – and – 3 – and take triangular shaped trim – 2 – off towards rear – arrow – . Remove A pillar lower trim General body repairs, interior – Repair Group 68 Disconnect multi-pin connectors – 1 – on A pillar – 2 – . Take cover – 1 – for wiring harness – 2 – out of body opening in the inner A pillar. Pull wiring harness out of A pillar at boots – 1 – between door and A pillar. Remove bolt – 1 – of door arrester – 2 – . To prevent damage to paint work, mask lower edge of fender – 2 – in area of lower hinge – 3 – with textile reinforced adhesive tape – 1 – . Pull cover cap –

WARNING! Disconnect battery Ground (GND) strap before working on electrical system, observing all cautions => Repair Manual; Electrical; Repair Group 27, Battery, disconnecting and reconnecting. Removing Note: Before disconnecting battery Ground (GND) strap obtain security code for radio with anti- theft coding. Remove driver’s airbag unit => page 69-50. Remove steering wheel => page 69-61. Note: For vehicles with steering angle sensor -G85-

Tools required: Medium Phillips screwdriver Small flat blade screwdriver Procedure: The transmission ECU is located underneath the carpeting directly in front of the front passenger seat. First remove the passenger kick panel trim located to the right in the passenger footwell. For Passat: The panel is fastened at the top by a clip and at the bottom with a phillips screw. The lower screw is under a small cover at the bottom of the panel. Pop off the cover with the small flat blade screwdriver and remove the screw. Pop the top clip by gently pulling at the top of panel. Pull the panel free, noting the way it clips

DESCRIPTION & OPERATION Heating and ventilation system is a blend type system. A heater control valve is not used. Coolant flows unrestricted through heater core. Interior temperature is regulated by a blend door which controls amount of air flowing through heater core. Blend door is operated by a cable connected to temperature control knob. Three knobs are used to control blower speed, air temperature, and air distribution. Fresh air blower has 4 speeds. Blower motor resistor is located on blower motor housing. ADJUSTMENTS MAIN SHUTOFF FLAP CABLE Install heater control panel. Adjust blower control

1995-96 STARTING & CHARGING SYSTEMS Volkswagen Starters Cabrio, Golf III, GTI, Jetta III DESCRIPTION Starter is a brush type, series-wound electric motor with an overrunning clutch. Field frame is enclosed by commutator end frame and drive bushing, and carries pole shoes and field coils. A splined armature shaft drive end carries drive assembly. TROUBLE SHOOTING NOTE: ON-VEHICLE TESTING STARTER DOES NOT CRANK ENGINE 1) Ensure battery is fully charged. Ensure electrical and ground connections are clean and tight. With ignition switch in START position, measure voltage at spade terminal of starter

SYSTEM OPERATION CHECK An air bag light is located on left side of instrument cluster. Air bag light is used to indicate readiness of system. Light glows when ignition switch is on or engine is started. Light should stay on about 3 seconds while air bag control unit performs an electronic test of system. If air bag light does not glow when ignition is on or does not go out after 3 seconds, a fault probably exists in system. If a fault occurs while ignition is on, it is stored in fault memory. Warning light will then glow and air bag system will be switched off. If warning light glows or flickers while driving, air

BRAKE PRESSURE REGULATOR NOTE: CAUTION: DO NOT adjust pressure regulator with brake pedal depressed. 1) Ensure fuel tank is full and spare tire is in trunk. Raise and support vehicle. Attach Pressure Gauges (VAG 1310) to left front brake caliper and right rear brake caliper/cylinder. Bleed pressure gauge and hoses through valve on gauges. 2) Lower vehicle and bounce rear of vehicle several times. Press on brake pedal until front brake pressure gauge reading equals pressure listed in 1st Reading column of BRAKE PRESSURES table. Hold brake pressure. Rear brake pressure gauge reading should

Free Volkswagen service manual deck model Jetta, Golf, GTI, from 1999 to 2005. The document contains information about common, technical data, Assembly, crankshaft, Cylinder block, cylinder head, Valvetrain, lubrication, cooling system, fuel supply, exhaust system, emission control and much more.

1989 Volkswagen Golf is very famous on era 1980-1990. The car is 2-door hatchback base, as it is powered by a 1.8 litre, 4-cylinder and produce 100-HP engine that works with 5-speed manual transmission. Section: Clutch, transmission, wiring diagram, steering control, planned service, heater system, engine, etc.

get

This handbook covers petrol, Turbo diesel, TDI 4-cylinder VR6 SOHC 12V, including Wagon. The manual contains the wiring diagram, troubleshooting procedure, standard equipment and much more. 1997 Volkswagen Passat 4-door sedan is available in two models: GLX and TDI. Standard safety equipment includes dual airbags, daytime running lights, side-impact and child safety locks.

Welcome to the world-wide family of Volvo owners. We trust that you will enjoy many years of safe driving in your Volvo, an automobile designed with your safety and comfort in mind. We encourage you to familiarize yourself with the equipment descriptions and operating instructions in this manual. We also urge you and your passengers to wear seat belts at all times in this (or any other) vehicle. And, of course, please do not operate a vehicle if you may be affected by alcohol, medication or any impairment that could hinder your ability to drive.

The Volvo 850 Saloon and Estate were introduced in 1992 and were a radical departure from the traditional Volvo large vehicle format. The 850 features transverse engine/transmission layout, front wheel drive and state-of-the-art suspension technology providing excellent handling and driveability for a large car. The engine used in the 850 range all fuel-injected, in-line, five cylinder units of 1984 cc, 2319 cc, or 2435 cc displacement. Both normally-aspirated and turbocharged version are available. The engine features a comprehensive engine management system with extensive emission control equipment. The 1992-1996 Volvo 850 (Haynes Service and Repair Manual) contains the information about Basic maintenance, Service your car, Fault finding, Roadside emergency, Pass the MOT, Reference section, Brakin system, Fuel and ignition systems, Electrical system, Engine, Wiring diagram with easy-to-follow layout. Total : 237 Pages.

The description and service procedures contain in this Volvo Trucks manual ( disassembly instruction ) are based on designs are methods studied carried out up to January 2008. The products are under continuous development. Vehicles and components produced after the above date may therefore have different specifications and repair methods. When this is judged to have a significant bearing on this manual, supplementary service bulletins will be issued to cover the changes. You can also download the 1992-1996 Volvo 850 [Haynes Service and Repair Manual].

Volvo V70 produced since 1996, the CUV mid-size 5, more than 80% of the Volvo V70s are sold in Europe. V70 XC received an upgrade in its suspension and equipped with a ground clearance of the soaring 8.2 min. "under the vehicle. It sets its versatility in a whole new level. Therefore this model, the V70 XC even attracts customers with customers SUV different producers. These statements Volvo VOLVO V70 and XC70 read rise before Your diving car.

Contains information about:

2008 Volvo V70/XC70 is a Roomy cars, powered from standard 3.2 litre 6-cylinder power plant, 6 automatic transmission speed geartronic ", five passenger seats, 37 cubic compartment, a new 40/20/40-split rear, optional pwer rear. This instruction will guide you to understanding all the controls and functions inside the V70/XC70 as Nuke security, Basic Guide while is riding on the road of solving problems. The owner of the content of the Manual: introduction, safety locks and alarm, Your driving environment, comfort and pleasure driving, during the travel, subsistence and specifications, scheduled maintenance, the index.

Pdf-download

Tags: 2008 volvo v70, volvo v70, xc70, castles, maintenance index

The Volvo XC90 is the first vehicle SUV looks look crossover wagon, Volvo Cross country and BMW X 5. Unlike the BMW new Volvo is Roomy with versatile Interior, that boasts a cargo more than Mercedes M-class. Volvo XC90 powered by turbocharged engines, five cylinders and 6-cylinder and we actually preferred 2.5 T 5 cylinder version. This guide provides basic car, equipment descriptions, instructions and maintenance

This document contains information about the 1994 960 cooling system Specification volvo, specification of the tape. Here is a brief description and illustration of ' the patterns of connections at the end of this document. Deflection is measured from the midway pressure applied to moderate a thumb on the longest belt run. The belt is self-adjusting. Identify belt routing (850 and 960) appears courtesy of Volvo cars of North America.

Volvo 400 and 460 is a car with front wheel drive, 5-door hatchback produced by the Swedish automaker volvo car. Both versions had a 1.7-litre Renault engine at startup. A turbocharged version offered 122 HP (91 kW) and a planned speed of 200 km/h (124 mph).

This manual contains information on the establishment and maintenance of a Volvo it should be noted that there are some differences between the versions of the model and market requirements; in this way, you can see the features described and pictured in this manual, which does not appear in the car. If you need more detailed information in relation to adjustments or repairs contact seller of Volvo. Manual index:

Remove the spinner control to the heater; Insert a small screwdriver to the posterior edge of each wheel. Remove the control panel heater (Insert two fingers to open and carefully pull the control panel). Remove the two screws (torx) upper anchorages on the control panel radiators. Carefully call out the vents with a small screwdriver. Press the catch on the downwards from the inside using a screwdriver.

Air Ducts to Panel vents. the mixing of the air. The Centre Panel of the vent. Reconnect the cables. Installing: electricity distribution unit bracket. The distribution of electricity. the control panel. Cantilever range radio. center console side panels. Installing: Glove box (back light). Panel in the area of CR (VI). Install the Panel on the left side of the dashboard. The cover of the parking brake. Ashtray holder (back light).

Boot, a half shaft, replacing the special tools: 951 2619, 999 2412 dismantling Note: preparatory work, see shaft Assembly; Service and repair. Delete Secure Boot shaft Vise with soft jaws. Remove the clamps of the shoes. Boot cut and remove it from the shaft. Check measurement wipe off grease from common constant speed. Measure the distance from the inner ring on the inner groove in the shaft.

Legend 1/1 passing a battery of 2/11, electronics, heater 2/12 Relay interference on fuel injectors fuel 3/49, the throttle switch 2/13 Relay Unit for controlling fuel injection 3/1 ignition switch 4/10, the ignition system 6/31 fuel pump 7/17 mass air meter, 8/5 Air control valve injectors fuel 8/6-11, 11/1-35-links 17/2, Test Socket-Lambdasond 31/13 grounding, starting with the grounding 31/14, with the earth ground transmission main console 31/32, the engine control unit for 4/8, the LH-jetronic 6/32 tank pump 7/15 Lambdasond

Note: Pressure cannot be removed individually. Electromagnetic control of vacuum is (electromagnetic valves): electromagnetic Valves open and close the vacuum lines of vacuum bells used to control the Sun, in response to electrical signals, usually a Few pressure that are installed are tightened securely, eliminating the risk of conversion and any hoses, heater replacement Note: this procedure shows the 940 model.

Note: Figures in the information services are used for various years and/or models. Some changes may occur. However, the most important information in illustrations is always correct. Preparations to remove the wheels on both sides. Remove the line pad assemblies Note: the recommended minimum pad thickness/Exchange limit during the installation of a new line of pad assemblies = 3,0 mm. Remove foundations springs and locating pins to the terminals of the brakes. Delete: is-is securing spring (3) carefully so as not to deform the protective caps (1) the two locating Pins

Volvo said that it may experience an occasional driver's air bag clockspring wiring connector for supplemental restraint System (SRS). If this condition, SRS will be permanently illuminated, together with the following message in the Module information drivers (DIM) "air bag service required SYSTEM". If the condition occurs while driving, and if the driver ignores warnings, should an accident occur where required is to deploy the air bag of driver, the driver's air bag may not deploy as expected or not implemented at all. This poses undue risk to the safety of motor vehicles.

Precautions always cut the current headlamps before replacing the lamp. Do not touch the core high-and low-light when working with high voltage and the risk of explosion. Delete the keys and lock the car. Allow the lamp to cool. When you replace the lamp with goggles and gloves. The glass bulb is Graz is filled with various gas and metal vapors which are under pressure. Do not touch the glass lamp. Only touch the lamp at the nest. Remove any finger of glass with a cloth and alcohol. The lamp must be used only in closed. Has been replaced with light-Xenon must be treated as hazardous waste and must be sent for recycling. Removal of ballast on the right side delete the filler of windshield-washer for better access, remove the screw,

Replace the Trunk lid lock, switch or motor (4-door) ZZB1. Removing the trunk lid lock units (4-door), remove the lock body, see below CA5. ZZB2. Install the trunk lid lock units (4-door) installation lock unit by the inverse procedure CA5. Lock the unit ZZB3. Remove Lock switch units (4-door): delete the blocking unit. cable with the socket on the back. Go up. Connector and pull on the cables. Note the position

The track connection between the fuel manifold and fuel distribution, you must use a hose-5116 and nipple 5265, Plug the open end of the hose with c(2004) 2566. Enable gauge cock to position 1, incoming hose 5116. B13 Check function of the fuel pump and tank pump pressure sensor located next to the expansion in the engine compartment. Disconnect the connectors from the sensor. Turn on the ignition. Connect the cables (connector) from the transmission to the ground. (Note: both in tubes, yellow/black, find out which one is the ground). The fuel should be run and clearly heard. B14 Check tank pump, Unscrew the CAP and the filler funnel. It is also possible to connect ammeter between fuse and electrical pumps. 740 1985 on: fuse 11 760 to 1987: fuse 11 760 1988/89: fuse current consumption 11/30: 1-2 (A). If it is running or pump: turn off the ignition.

Transmission Replacement Tools Required J 42371 Hydraulic Clutch Line Separator Removal Procedure 1. 2. 3. 4. 5. 6. Shift the transmission into 3rd or 4th gear. Remove the shift lever assembly. Drain the transmission fluid. If vehicle is a 2 wheel drive (2WD), remove the propeller shaft. If vehicle is a 4 wheel drive (4WD), remove the transfer case. Using J 42371, push back on the white plastic sleeve on the quick connect in order to separates the hydraulic clutch line from the clutch actuator quick connect. 7. Disconnect the following engine wiring harness electrical connectors:

1. 2. 3. 4. 5. Install the spring retainers to the synchronizer hub. Align the scribe marks previously made on the synchronizer hub and the synchronizer sleeve. Install the synchronizer hub to the synchronizer sleeve with the three struts. Install the main drive synchronizer stop ring to the synchronizer sleeve. Install the drive sprocket to the mainshaft. 6. Install the synchronizer assembly to the mainshaft. 7. Install the synchronizer snap ring to the mainshaft. 8. Use a soft faced hammer in order to install the following components into the annulus gear: • The input gear • The planetary assembly 9. Install the snap ring to the input bearing. 10. Apply RTV GM P/N 12345739 or equivalent to the input shaft bearing retainer mating surfaces. 11. Apply threadlocker GM P/N 12345382 or equivalent to the input shaft bearing retainer bolts. 12. Install the input shaft bearing retainer and the input bearing retainer

Subject: Models: 2009 Corvette LS7 and LS9 Engine Replacement Information 2009 Chevrolet Corvette with a 6.2L (RPO LS9) or 7.0L (RPO LS7) Engine in the United States of America The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI. Condition/Concern: This is to announce a temporary program for 2009 Z06 and ZR1 Corvettes in the U.S.A. with major engine failures. In an effort to gain product knowledge quicker, Chevrolet would like to provide the opportunity for the customer to allow their Z06 or ZR1 Corvette to be picked up by special carrier and returned to the Bowling Green Assembly Plant to have the engine exchanged. If the customer agrees, General Motors will arrange to have a complete engine

This PI was superseded to advise dealers there is no repair for early oil change messages or erratic OlM operation. Please discard PIP4540B. The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI. Condition I Concern: A dealer may encounter a customer concern of the oil life monitor (OlM) percentage dropping too qUickly, or an early oil change message. A customer utilizing the oil life monitor may be directed to change the oil at (or near) 1000 mile intervals. Recommendation Ilnstructions: Please do not replace the IPC or ECM

Circuit Description The inflatable restraint steering wheel module deployment loop consists of a steering wheel module, steering wheel module coil, steering wheel module high control, and steering wheel module low control circuits. Shorting bars are used on the steering wheel module connector as well as the steering wheel module coil connector which will short together the steering wheel module high and steering wheel module low control circuits when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing. When the ignition is turned ON, the inflatable restraint sensing and diagnostic module (SDM) performs continuous diagnostic tests on the deployment loops to check for proper

Callout Caution: Refer to SIR Inflator Module Handling and Storage Caution in the Preface section. Caution: Refer to SIR Caution in the Preface section. Preliminary Procedure Disable the supplemental inflatable restraint (SIR) system. Refer to SIR Disabling and Enabling . Retainer Procedure 1 On the back side of the steering wheel, there are 2 access holes. Using a 3-4 mm T handle allen wrench , insert in a cross car (Horizontally) direction and slightly outboard (handle towards I/P) push in 40mm (1 1/2in) to engage release spring. Component Name Steering Wheel Inflatable Restraint Module Procedure 1. Release the connector position assurance (CPA) retainer. 2. Disconnect the electrical connectors. 3. Fully deploy the module before disposal. If the module was replaced under warranty, fully deploy and dispose of the module after the required retention period. Refer to Inflator Module Handling and Scrapping .

Circuit Description The auxiliary brake system provides hydraulic fluid flow within the brake booster if the engine is OFF and the brake is applied. The system consists of the following 3 basic components: • The power brake booster pump motor relay • The power brake booster fluid flow switch • The power brake booster pump motor The multifunction alarm module (MFAM) performs a 4 second bulb check on the AUX BRAKE indicator immediately after the engine is cranked or started. The MFAM illuminates the indicator by supplying voltage to the lamp. During the bulb check, the MFAM also performs a diagnostic which tests the power brake booster pump motor relay, the power brake booster fluid flow switch and the power brake booster

Caution: Refer to Gasoline/Gasoline Vapors Caution in the Preface section. Important: There are several types of Plastic Collar Fuel and Evaporative Emission Quick Connect Fittings used on this vehicle. • Bartholomew (1) • Q Release (2) • Squeeze to Release (3) • Sliding Retainer (4) • Push Down TI (5) The following instructions apply to all of these types of Plastic Collar Quick Connect Fittings except where indicated. 1. Relieve the fuel system pressure before servicing any fuel system connection. Refer to the Fuel Pressure Relief . Caution: Refer to Safety Glasses Caution in the Preface section. Notice: Refer to Fuel and Evaporative Emission Hose/Pipe Connection Cleaning Notice in the Preface section. 2. Using compressed air, blow any dirt out of the

SIR component location affects how a vehicle should be serviced. There are parts of the SIR system installed in various locations around a vehicle. To find the location of the SIR components refer to SIR Identification Views . There are several reasons for disabling the SIR system, such as repairs to the SIR system or servicing a component near or attached to an SIR component. There are several ways to disable the SIR system depending on what type of service is being performed. The following information covers the proper procedures for disabling/enabling the SIR system. SIR Service

New Fixes/Features:
* Fixed issue where the power button recovery is for cold boot path only.
* Fixed issue where provisioning record in Setup displays a “Setup IP” that is not correct.
* Updated Intel ME firmware to the revision: 7.0.4.1197.
* Updated processor support.
* Added support for PCH B3 stepping.

About This Release:
* February 22, 2011
* ME Firmware: 5MB SKU 7.0.4.1197 Production
* MEBx Code: Based on Version 7.0.0.0053
* Integrated Graphics Option ROM: Build 2089 PC 14.34
* SATA RAID Option ROM: Intel(R) RAID for SATA – v10.1.0.1008
* LAN Option ROM: Intel(R) Boot Agent GE v1.3.65

New Fixes/Features:
* Fixed issue where system hangs at POST code 2D.

About This Release:
* February 28, 2011
* QPI Reference Code: Based on Revision 1.85
* ICH10 SATA RAID Option ROM: 10.0.0.1046
* Marvell 9128 SATA Gen 3 Option ROM: 1.0.0.1027
* Marvell 6121 SATA Gen 2 Option ROM: 1.2.0.29
* LAN Option ROM: Intel(R) Boot Agent PXE GE v1.3.65
* LAN Option ROM: Intel(R) Boot Agent PXE Base Code (PXE-2.1 build 089)

New Fixes/Features:
* Fixed issue with Intel ME firmware update.

About This Release:
* January 20, 2011
* Integrated Graphics Option ROM Revision on TM: 2086 PC 14.34
* Integrated Graphics Option ROM Revision on TM Legacy: 2086 PC 14.34
* PXE LAN Option ROM Revision: PXE 2.1 Build 089, v1.3.65
* SATA RAID Option ROM Revision: 9.5.0.1037
* ME Firmware: 8MB SKU 6.1.20.1059
* MEBx Code: Based on Version 6.1.0.0005

New Fixes/Features:
* Fixed issue where the power button recovery is for cold boot path only.
* Fixed issue where provisioning record in Setup displays a “Setup IP” that is not correct.
* Updated Intel ME firmware to the revision: 7.0.4.1197.
* Updated processor support.
* Added support for PCH B3 stepping.

About This Release:
* February 22, 2011
* ME Firmware: 5MB SKU 7.0.4.1197 Production
* MEBx Code: Based on Version 7.0.0.0053
* Integrated Graphics Option ROM: Build 2089 PC 14.34
* SATA RAID Option ROM: Intel(R) RAID for SATA – v10.1.0.1008
* LAN Option ROM: Intel(R) Boot Agent GE v1.3.65

New Fixes/Features:
* Fixed issue where the power button recovery is for cold boot path only.
* Fixed issue where provisioning record in Setup displays a “Setup IP” that is not correct.
* Updated Intel ME firmware to the revision: 7.0.4.1197.
* Updated processor support.
* Added support for PCH B3 stepping.

About This Release:
* February 22, 2011
* ME Firmware: 5MB SKU 7.0.4.1197 Production
* MEBx Code: Based on Version 7.0.0.0053
* Integrated Graphics Option ROM: Build 2089 PC 14.34
* SATA RAID Option ROM: Intel(R) RAID for SATA – v10.1.0.1008
* LAN Option ROM: Intel(R) Boot Agent GE v1.3.65

New Fixes/Features:
* Fixed issue with Intel ME firmware update.

About This Release:
* January 20, 2011
* Integrated Graphics Option ROM Revision on TM: 2086 PC 14.34
* Integrated Graphics Option ROM Revision on TM Legacy: 2086 PC 14.34
* PXE LAN Option ROM Revision: PXE 2.1 Build 089, v1.3.65
* SATA RAID Option ROM Revision: 9.5.0.1037
* ME Firmware: 8MB SKU 6.1.20.1059
* MEBx Code: Based on Version 6.1.0.0005

New Fixes/Features:
* Updated ICH RAID Option ROM to revision 10.1.0.1008.
* Updated LAN PXE ROM to revision 1.3.65.
* Added codes to support error beep and front LED blink feature.
* Added codes to check firmware version to prevent BIOS recovery from an incorrect BIOS file.
* Fixed issue where the splash shows three times during POST when burning with a clean BIOS ROM file.

New Fixes/Features:
* Updated the ME firmware to the version of 5.2.40.1037.

About This Release:
* February 11, 2011
* CBQ4510H.86A.0129.2011.0211.1459
* ME Firmware Revision: 5.2.40.1037
* Integrated Graphics Option ROM Revision: 1940
* SATA RAID Option ROM Revision: 8.6.0.1007
* PXE LAN Option ROM Revision: Intel(R) Boot Agent GE v1.3.53

New Fixes/Features:
* Updated the ME firmware to the version of 5.2.40.1037.

About This Release:
* February 11, 2011
* CBQ4510H.86A.0129.2011.0211.1459
* ME Firmware Revision: 5.2.40.1037
* Integrated Graphics Option ROM Revision: 1940
* SATA RAID Option ROM Revision: 8.6.0.1007
* PXE LAN Option ROM Revision: Intel(R) Boot Agent GE v1.3.53

New Fixes/Features:
* Updated Intel ME Firmware: 7.0.4.1197
* Updated processor support.
* Updated HyperBoot feature.

About This Release:
* February 15, 2011
* ME Firmware: 7.0.4.1197 CPT_1.5M_Production.BIN
* Integrated Graphics Option ROM: None
* SATA RAID Option ROM: v10.0.0.1046
* LAN Option ROM: v1365 PXE 2.1 Build 089

New Fixes/Features:
* Fixed issue where the watchdog timer is not able to catch system hang.
* Improved BIOS POST time for detecting and accessing USB mass storage devices.
* Updated Intel® ME firmware to version 7.0.4.1197.
* Fixed CPU fan failure event.
* Fixed FSC Dynamic Screen updates 1 sec.
* FSC Fix for processor TControl, and updated FSC Stack.
*

New Fixes/Features:
* Updated Intel ME Firmware: 7.0.4.1197
* Updated processor support.
* Updated HyperBoot feature.

About This Release:
* February 15, 2011
* ME Firmware: 7.0.4.1197 CPT_1.5M_Production.BIN
* Integrated Graphics Option ROM: None
* SATA RAID Option ROM: v10.0.0.1046
* LAN Option ROM: v1365 PXE 2.1 Build 089

New Fixes/Features:
* Added Support for new SPI Flash part (Winbond W25Q16BV).
* Fixed issue where Intel Desktop Utilities displays no data when UEFI Boot is enabled.
* Fixed issue where BIOS still requires password when user password is not installed and user access level is full.
* Fixed issue where POST Function Hotkeys display on the bottom of the screen before flash