Online repair manual

Overture Audio Power Amplifier Series Dual 20-Watt Audio Power Amplifier with Mute and Standby Modes

The LM1876 is a stereo audio amplifier capable of delivering typically 20W per channel of continuous average output power into a 4 or 8 load with less than 0.1% THD+N.

Each amplifier has an independent smooth transition fade-in/out mute and a power conserving standby mode which can be controlled by external logic.

The performance of the LM1876, utilizing its Self Peak Instantaneous Temperature (°Ke) (SPiKe™) protection circuitry, places it in a class above discrete and hybrid amplifiers by providing an inherently, dynamically protected Safe Operating Area (SOA). SPiKe protection means that these parts are safeguarded at the output against overvoltage, undervoltage, overloads, including thermal runaway and instantaneous temperature peaks.

Circuit Diagram

Dual 20-Watt Audio Power Amplifier Circuit Diagram

Applications

High-end stereo TVs

Component stereo

Compact stereo

Features

SPiKe protection

Minimal amount of external components necessary

Quiet fade-in/out mute mode

Standby-mode

Isolated 15-lead TO-220 package

Non-Isolated 15-lead TO-220 package

Wide supply range 20V - 64V

A small audio test generator is very useful for quickly tracing a signal through an audio unit. Its main purpose is speed rather than refinement. A single sine-wave signal of about 1 kHz is normally all that is needed: distortion is not terribly important. It is, however, important that the unit does not draw too high a current. The generator described meets these modest requirements. It uses standard components, produces a signal of 899Hz at an output level of 1V r.m.s. and draws a current of only 20µA. In theory, the low current drain would give a 9 V battery a life of 25,000 hours. The circuit is a traditional Wien bridge oscillator based on a Type TLC271 op amp. The frequency determining bridge is formed by C1, C2 and R1–R4. The two inputs of the op amp are held at half the supply voltage by dividers R3-R4 and R5-R6 respectively.

Resistors R5 and R6 also form part of the feedback loop. The amplification is set to about ´3 with P1. Diodes D1 and D2 are peak limiters. Since the limiting is based on the non-linearity of the diodes, there is a certain amount of distortion. At the nominal output voltage of 1 V r.m.s., the distortion is about 10%. This is, however, of no consequence in fast tests. Nevertheless, if 10% is considered too high, it may be improved appreciably by linking pin 8 of IC1 to ground. This increases the current drain of the circuit to 640 µA, but the distortion is down to 0.7%, provided the circuit is adjusted properly. If a distortion meter or similar is not available, simply adjust the output to 1 V r.m.s. Since the distortion of the unit is not measured in hundredths of a per cent, C1 and C2 may be ceramic types without much detriment.

Here is the circuit diagram of superb mini audio power amplifier, That can be power with 4.5 volt dc to 18 volts dc (maximum). This amplifier is based on TDA1015, Product of NXP Semiconductors formerly PHILIPS Semiconductors. The TDA1015 is a monolithic integrated audio amplifier circuit in a 9-lead single in-line (SIL) plastic package. The device is especially designed for portable radio and recorder applications and delivers up to 4 watt in a 4 ohm load impedance. The very low applicable supply voltage of 3,6 V permits 6 V applications.

click on the images to enlarge

Parts:

R1330K
R25.6K
R34.7R
C11uF-25V
C21uF-25V
C3100pF
C4100nF-63V
C5182pF
C6224pF
C7100uF-25V
C8100nF-63V
C910uF-25V
C101KuF-25V
IC1TDA1015

Applications:

• In-car use
• Your own unique application
• Power amplifier for audio projects
• For use with portable audio equipment
• Small but powerful multi-purpose amplifier

Special features:

• Low current drain
• High output power
• Thermal protection
• High input impedance
• Separated preamplifier and power amplifier
• Limited noise behavior at radio frequencies
• Single in-line (SIL) construction for easy mounting

Specification:

• Quiescent current : 12mA
• Thermal and short circuit protection
• Frequency Response : 60Hz - 15Khz
• Max. output power : 3W (4ohm/12V)
• Input sensitivity : 20-15mV selectable
• Power supply : 4.5 - 15V DC @ 400mA