Online repair manual

This installation guide is designed to complement the instructions to install the BMW to help you with installing Sirius receiver BMW X 5 (E53) with navigation. I chose Terk SIR3 low profile magnetic mount antenna and mounted in the spoiler. As a result of this tutorial will not cover the installation of antennas Sirius BMW and you must follow instructions, along with Sirius satellite antenna Kit BMW

D110.For the BMW E39 5 series M5 ' 97-' 03 – standard audio cable
We are going to proceed as follows:
-Accommodation factory amplifier
-Mounting on new amplifier
-Power connections for the new amplifier
-Audio inputs for the new amplifier
-Join a new amplifier new subwoofer enclosure
-Installation of the new enclosure subwoofer
Tuning/testing new amplifier

There are some steps to update the radio at the BMW E34:
I. in this update we consider shortcomings of the bass factory
and underpowered factory amp. Exchange systems are not equipped with subwoofers. Thus first investments better add to the existing system. To add a subwoofer for the plant systems we need an amplifier to power it. We have several choic-es here, depending on the budget.

Unit is designed to ensure the integration of your car in to a mobile phone and Bluetooth ® enabled mobile phone. This kit is designed to provide Bluetooth in your car quickly and easily! Just find your phone in your car connector, plug the unit into the slot in the MIC if your vehicle is not yet one and your done!
This kit provides integration with the stereo switch off the radio and use built-in BMW

BMW fast start installation (dual-connected and managers-stock ignition advance, 1981-1995 model years with electronic ignition systems factory, see the complete guide installation troubleshooting &).
1. open the "black box" (part 1), set the dip switch according to the sticker (part # 10). Apply a sticker up.
2. fasten the black box (part 1) for the aluminum plate (part 5) with bolts, washers (part # 11).

KIT COMPONENTS
• Housing • Radio Radio trim plates • brackets clips Panel PC-7503 • (4)
• (8) PFH-12 mm flush mount ISO screws • (2) the MBM-12 Phillips screws
95-9307B BMW 5 SERIES DASH SHOWDOWN 1997-2003
1. disconnect the negative battery terminal to prevent accidental short circuits.
2. delete the volume by dragging to the rear of the vehicle.

CAN bus owners to install fuse block with the ignition switch moved to simplify installation and maintenance of all electrical accessories. Hyper-Lites and other accessories may be installed in fuse block without interference from the can bus system.

Warning: this product should only be performed by an experienced welder!Installation:
Note: refer to figures A-E for reference before you begin installing braces-side airport loading/unloading and return the data during the installation process.
The figure shows the finished installation bracket CC products/San Jose BMW Airhead side for general reference.
Figure b shows the upper end of the brace Airhead side where it attaches to the frame
(Note: leave at least 1/2 "intervals below at the bottom of the fuel tank).
Figure c shows how the side brace airfield embarkation/disembarkation should be removed from the tube air inlet.
(D) while the illustration shows how the bottom edge (beveled end) fits frame at the rear of the bike.
Figure e shows one threaded cones properly welded to the frame and painted.

Installation steps:
1. ensure airport loading/unloading side braces fully assembled (threaded cones, firmly screwed in braces on both ends).
2. Holding the airfield embarkation/disembarkation side brace in their proper position (figures A-D) to note the location where you want to weld the front and rear threaded cones to the frame.
Note: the lower (rear) Airhead side brace was canted, for reference.
Note: make sure that the left and right airfield embarkation/disembarkation side braces are located in the same way.
3. Select a frame and remove paint in relevant areas, using Emery cloth for the preparation of the surface of the frame for welding.
Note: dimensions and Mark twice, weld once!
4. keep collected airfield embarkation/disembarkation side braces in their respective positions and tactics to Weld the top and bottom. Perform this step to the top (front) and lower (rear) end of the airfield embarkation/disembarkation side brackets on both sides of the bike.
5. Using removable tape, mark each brace side airfield embarkation/disembarkation or "left" or "right" to make sure they are replaced with the corresponding side of the bike after disassembly.
6. remove the screws and braces side airfield embarkation/disembarkation of welded tactics, threaded cones. Complete welding threaded SAE motorcycle frame on all four points.
7. clear or delete any weld splatter or paint to protect screw Cone and frame corrosion (see Figure E).
8. Peremontaž airport loading/unloading side braces for threaded cones, preserving its original orientation left side/right side.
Note: the lower (rear) Airhead side brace was canted, for reference.
9. torque hex bolts 7 foot/pounds.

Source: http://www.sjbmw.com/_documents/instructions/319_part.pdf

Flat head screwdrivers and Phillips head screwdriver or T20 torx driver T15 and only the elements necessary to complete this installation. Also expired credit card or similar (see step 1) is not required. Note that this setting is made on the E90 LCI. Installation is similar to vehicles, non-DEVELOPMENTAL, depending on whether you have a button bar for the heated seats,

THESE STEPS MUST BE PERFORMED IN THE FOLLOWING ORDER:
1. place motorcycle on his centerstand on level ground and lift the front seat. Remove the screws (2), which took a back seat in place with a 5 mm Allen key. Remove the seat and set it aside.